食色软件app下载_食色视频app_食色官方

Welcome to the official website of Shanghai Jibei Air Treatment Equipment Co., Ltd.!
30
National Sales Hotline:
4008-829-816

Air-cooled thermostat dehumidifier

2018-11-18
Temperature and dehumidifier.jpg
  • Product Details
  • Basic parameters

Performance profile:

The air-cooled temperature-adjusting dehumidifier uses air-cooling and temperature-adjusting (with outdoor condenser) to control the temperature rise or fall while dehumidifying. It has the function of air conditioning and integrates dehumidification and refrigeration. The air supply method has front air. There are several forms of ejection air and duct air supply, and users can choose according to specific conditions.

Features:

1. The fully enclosed refrigeration compressor, expansion valve, solenoid valve and other components selected by the unit are imported products.

2. The control switch adopts touch buttons, and the operation panel has the function of operation indication and fault display.

3. The fan equipped with the unit adopts high-performance, low-noise centrifugal fan, which has the advantages of low noise, large air volume and high static pressure.

4. The unit can achieve central control, and configure communication interfaces according to user requirements to achieve centralized control and display of long-distance computers.

5.The unit runs smoothly, is easy to operate, has a beautiful appearance, and requires a small amount of maintenance.

Technical Parameters:


全热交换新风除湿机

Working principle: The full heat exchange fresh air dehumidification and purification system is an improved air supply and exhaust air dehumidification system with heat recovery function based on the two-way fresh air system. The air supply and exhaust are completed by a host (two fans), and a heat exchange module is added inside the host, which can quickly absorb and release heat, ensuring sufficient heat exchange between the air, exhausting outdoor air and sending air. The fresh air entering the room is exchanged in this total heat exchange device. When the indoor exhaust air and fresh air flow through the core of the heat exchanger in a crosswise manner, due to the temperature difference and steam partial pressure difference between the air flows on both sides of the air separation plate, When two air flows pass through the partition plate, a heat and mass transfer phenomenon appears, causing a total heat exchange process. The fresh air outside is pumped into the equipment through the primary effect G4 + intermediate effect F7 + ** H13 (HEPA) + negative ion UV sterilization device through the direct expansion type dehumidification fan. When the humid air passes through the heat exchanger, the The water condenses into water and is discharged from the drip tray at the lower part of the evaporator. At the same time, the dry air is delivered to the room. At this time, the dirty air in the room is finally discharged to the outside after heat exchange. This continuous circulation gradually reduces the indoor humidity, and also solves the problem. The problem of sweltering indoors and the continuous introduction of fresh air have improved the quality of indoor air and environmental comfort. Features: ☆ Full-automatic fresh air dehumidification, the equipment has 24 hours working characteristics. ☆ One-time installation with level correction function makes installation easier and more convenient. ☆ A heater can be installed at the air outlet of the equipment to further heat the dry air. ☆ The heat exchanger can be washed with water, and the evaporator and condenser are epoxy-coated, which is more resistant to corrosion. ☆ Condensate water has the function of positive pressure drainage, no need to do sinking bend, and greatly reduce the height of the ceiling. ☆ High heat exchange efficiency. The equipment adopts advanced countercurrent structure design, which can greatly improve heat exchange efficiency. ☆ Low noise and high static pressure double-speed or stepless speed-regulating centrifugal fan can meet the adjustment and switching of different air volume and air pressure. ☆ Condensate hot-change core adopts ** internal thread sleeve blue shutters, and condensate pan adopts SUS304 stainless steel. ☆ Equipment can be added and expanded system functions arbitrarily, HEPA ** filtration and negative ion and UV sterilization and purification can be added. ☆ The control function of the forced replacement of the air purification module further improves the quality of air purification and the service life of the product. ☆ The refrigerant filled in the equipment is environmentally friendly R410A or R134A refrigerant, and the compressor is Panasonic or Embraco. ☆ Fresh air purification system integrates fresh air and dehumidification into one system. Less maintenance costs, improved comfort and energy savings. ☆ German intelligent control module fool-type operation, easy to remember after simple setting, comes with R486 communication protocol and intelligent APP. ☆ The shell of the equipment is welded and sprayed from cold rolled sheet metal. The device comes with a self-balanced central fresh air introduction function, and excessive exhaust gas is discharged. ☆ The core program of the device without the intervention of electronic components is integrated in the wire-control operator, which reduces the failure rate of the product and improves the user experience. ☆ The device has the patented design of LUKO **, which makes the temperature of the dry wind sent to the room consistent with the indoor ambient temperature while total heat exchange and air replacement, achieving isothermal air replacement and saving energy. ☆ Two-way ventilation, indoor and outdoor two-way ventilation, equal replacement of fresh air and dirty air, positive and negative pressure operation can be realized according to customer requirements. Fresh air and exhaust air are completely separated to avoid cross infection. ☆ Built-in static heat exchanger, the heat exchange efficiency is more than 80%, and the cooling and heating load (room temperature) is not affected by the fresh air, which greatly reduces the energy required by the fresh air and achieves maximum energy saving. Fresh air full heat exchange bi-directional flow dehumidification and haze purification system parameter table Fresh air double flow dehumidification and haze purification system parameter table (no total heat exchange)

酒窖专用恒温恒湿机

Product introduction: The wine cellar constant temperature and humidity machine solves the requirements of different wines on the storage environment. By installing a wine cellar dehumidifier, the temperature and humidity required for various wine storage can be freely set. This improves the higher quality of the wine. Equipment performance characteristics: The energy-saving and environmental protection unit adopts imported brand Panasonic compressors, high-quality EC fans, and reasonable system design to make the whole machine run more energy-saving. The compact and compact body design, reasonable color matching, circular air vents and double doors The hinge structure design makes the whole machine more beautiful to control. ** Stable electrical control components are all international brand products such as Schneider in France. The automatic controller adopts the Italian Carel programmable control system, which has high stability, strong adaptability and control methods. Diversified, simple and flexible operation, independent control or centralized control, configurable communication interface for remote monitoring. The unit's high-performance electronic electrode humidifier has no pollution to the indoor air; there is no special requirement for water quality, and the independent humidifier control board can automatically control the water level and humidification electrode current according to the humidification requirements to achieve high-precision control. Adopting Swiss temperature and humidity sensor and precise valve control logic design, the temperature and humidity control accuracy is higher. The quiet-running unit adopts the ** low-noise EC fan; the structure of the static pressure box, and the inner wall is attached with heat-insulating and sound-absorbing materials, which effectively reduces the noise of the whole machine and achieves quiet operation. The appearance of the whole machine is safe and reliable. The whole metal structure design is adopted. The fireproof insulation material is included. The water pan is made of stainless steel for higher security. The system is equipped with multiple protections such as high and low pressure protection, overload protection, water leakage protection, over temperature protection, humidification protection, etc. Function, the whole machine passes rigorous testing to ensure more stable equipment operation, longer life and convenient installation. The unit is hoisted, and the ultra-thin fuselage design effectively reduces the equipment space occupation rate. The whole machine is installed in the ceiling through a boom. The unit is equipped with lifting ears for easy installation. The air inlet and outlet flanges use a round flange structure for simpler installation. The built-in fresh air electric damper requires no external settings. Convenient, flexible and simple design makes maintenance extremely easy. The inspection door panel adopts a hinge structure, which can be easily opened without removing a screw, and the internal parts are easy to maintain. Equipment parameter table

耐高温除湿机

Product introduction: The high temperature resistant dehumidifier has the function of dehumidifying at a higher ambient temperature, which solves the problem that the general dehumidifier cannot be used at a higher temperature environment, expands the scope of use of the dehumidifier, and makes the application field of the dehumidifier more extensive. . The reserved R485 communication interface can realize the centralized control of the humidity sensor fault self-diagnosis function. The microcomputer automatic defrost is more reliable and accurate. The continuous drainage function of all metal components and electrostatic sprayed sheet metal casing hoses is equipped with universal wheels at the bottom for free movement. Selecting frequency conversion technology can save power by 10%. Core components: Adopt imported brand compressors: brand guarantee, strong power output, high speed, high dehumidification efficiency. The compressor and main accessories are designed to operate normally in different environments through scientific and reasonable design of the refrigeration system. It overcomes the shortcomings of the compressor industry models such as insufficient cooling capacity and dehumidification capacity, the unit frequently starts up and has a high failure rate. At the same time, it improves the product's service life. The two (evaporator & condenser) 0.1mm blue hydrophilic aluminum foil material has fast condensation speed and full copper tube design, which greatly improves the dehumidification efficiency. Aluminum fin hydrophilic film condenser & evaporator, anti-stain cleaning ability, internally threaded copper tube, greatly improving the efficiency of dehumidification. High-quality cooling fan. Strong operation, ventilation and heat dissipation. The effect is remarkable. Turbine centrifugal fan metal shell, durable; strong wind. , Airflow output is bigger and faster. With U-shaped air duct, noise reduction and noise reduction, strong wind greatly improves dehumidification rate. Large circulation air volume is widely used in wood, seeds, tea, aquatic products, medicine, food, edible fungi and other fields. The product has a large applicable area, strong dehumidification, and can strongly remove moisture from materials. It is fast drying, energy-saving, and the whole series is based on the cabinet vertical design. The vertical air from the top can increase air circulation and make the entire place Balanced dehumidification. Equipment parameter table:

耐低温除湿机

Product introduction: Low temperature resistant industrial dehumidifier is specially designed for low temperature environment dehumidification (0 ℃ -8 ℃). It uses optimized system structure design. Under low temperature environment, the moisture in the air condenses faster on the surface of the fins, and the frost layer forms. More uniform, solving the problems of low temperature use of traditional dehumidifiers, uneven distribution of frost layers, and slow frost condensation speed; the use of electronic valve cold and hot switching defrost design, faster defrost, and solving the traditional dehumidifier unit application in low temperature environment, The defrost speed is slow and the defrost is incomplete, which causes the dehumidification effect to be not obvious. The characteristics of fast defrost and fast defrost of the unit speed up the dehumidification efficiency in low-temperature space and make the unit operate more reliably in low-temperature environments. Performance characteristics: High-sensitivity temperature measurement control panel adopts Schneider components, high sensitivity, stability and reliability. The R485 communication interface is reserved to realize centralized control of humidity sensor fault self-diagnostic function. Microcomputer automatic defrost, more reliable and accurate; all metal components and static electricity Core components of spray-painted sheet metal casing: international brand strong power compressor compressors and main accessories are designed scientifically and rationally through the refrigeration system. The hoses are continuously drained with universal wheels at the bottom. The free movement and the use of frequency conversion technology can save 10% of electricity. Adopting high-quality brands such as Danfoss refrigeration components, four-way reversing valves are suitable for heat pump systems such as central, unit, and room air conditioners. By switching the DC path of the refrigerant, the cooling mode and heating mode can be converted to evaporators and condensation. Aluminum fin hydrophilic film, condenser / evaporator, anti-stain cleaning ability 0.1mm hydrophilic aluminum foil material, fast condensation, greatly improve the efficiency of internally threaded copper pipe, greatly improve the efficiency of dehumidification turbo centrifugal fan with U-shaped air duct , Noise reduction, noise, strong wind greatly improved dehumidification rate large circulation air volume equipment parameter table:

升高温除湿机

Product introduction: The high-temperature dehumidifier has reached the advanced level at home and abroad after several upgrades. It is the third generation product of the heating type dehumidifier, with an average thermal efficiency of about 85%. This series of heating dehumidifiers use centrifugal fans and use electricity. As the heat source with the compressor, the centrifugal fan is used to heat the air by convective heat exchange of the heat exchanger, and the laminar flow of the hot air passes through the drying plate to transfer heat with the material. It is also equipped with a fully automatic constant temperature control system and a microcomputer control system option. The fully automatic control system can choose the best drying temperature and humidity according to the technological requirements of different products. It completely solves many problems such as long drying time, high temperature and large energy consumption in other drying methods. It has unparalleled characteristics. Performance characteristics: the use of a centrifugal fan, low noise and other characteristics, the material is dried uniformly and quickly. The material does not deform, crack, change color, do not deteriorate, and does not oxidize and dry to protect the color, fragrance and taste of the dry matter more effectively. Easy to operate and effective ingredients, good rehydration after drying, low nutrient loss, and long-term storage period, after setting the parameters, automatic control can be realized, high reliability, less investment, quick results, and can be used to transform the old kiln, garage, etc. It can be migrated and save floor space. It is simple and convenient. Core components: PTC corrugated radiator: PTC radiator uses PTC ceramic heating element and aluminum heat sink. This type of PTC heat sink has the advantages of small thermal resistance and high heat transfer efficiency. This type of automatic constant temperature, power-saving electric heater has a prominent feature: its safety performance is that when the fan fails to stop, the PTC heat sink will not fully radiate, and its power will automatically drop sharply. The temperature is maintained at the Curie temperature (usually around 250 ° C), so that the surface of the electric heating tube heater does not cause "redness", which can cause burns and fire. And other security risks. High-performance compressor: Imported brand compressor: brand guarantee, strong power output, high speed, high dehumidification efficiency. The compressor and main accessories are designed to operate normally in different environments through scientific and reasonable design of the refrigeration system. It overcomes the shortcomings of the compressor industry models such as insufficient cooling capacity and dehumidification capacity, the unit frequently starts up and has a high failure rate. At the same time, it improves the product's service life. Two devices (evaporator & condenser): 0.1mm blue hydrophilic aluminum foil material, fast condensation speed, full copper tube design, greatly improved dehumidification efficiency. Aluminum fin hydrophilic film condenser & evaporator, anti-stain cleaning ability, internally threaded copper pipe, greatly improving the efficiency of dehumidification. Turbo centrifugal fan: metal shell, durable; strong wind, airflow output is larger and faster. With U-shaped air duct, noise reduction and noise reduction, strong wind greatly improves dehumidification rate. Large circulation air volume is widely used in wood, seeds, tea, aquatic products, medicine, food, edible fungi and other fields. The product has a large applicable area, strong dehumidification, and can strongly remove moisture from materials. It is fast drying, energy-saving, and the whole series is based on the cabinet vertical design. The vertical air from the top can increase air circulation and make the entire place Balanced dehumidification. Equipment parameter table:

风冷降温除湿机

Product introduction: The cooling and dehumidifier has the functions of dehumidification and cooling, but the cooling capacity is not adjustable. It is suitable for dehumidification occasions with large heat and humidity load and no precision requirements for temperature. Performance characteristics: exquisite structure, simple and reasonable. The structure of the air supply system and the refrigeration system is relatively combined. The air supply system adopts the industrial design of the outer rotor centrifugal fan to achieve the direct exhaust without the need to install fans and pipes. It is particularly suitable for large areas. The warehouse building with a higher storey has stable performance and reliable quality. The compressor also uses a fully-enclosed scroll compressor. Compared with piston compressors, the number of wearing parts is reduced and the liquid compression resistance is strong. However, it cannot achieve temperature adjustment and human control. Optimization Energy saving, strong dehumidification capacity of the unit, high operating efficiency. Configuration of high and low pressure, antifreeze, oil pressure protection, overload protection. Compressor three-minute delay protection, under-reverse protection and other multiple safety protections. The operation is safe and stable. The fittings are designed scientifically and reasonably through the refrigeration system. Normal operation in different environments overcomes the lack of refrigeration and dehumidification capacity of compressor industry models. The shortcomings of frequent start-up of the unit and high product failure rate also increase the product use time. Evaporator & Condenser Aluminum fin hydrophilic membrane, condenser / evaporator, anti-stain cleaning ability. 0.1mm hydrophilic aluminum foil material, rapid condensation, and greatly improved efficiency. Internally threaded copper pipe greatly improves the efficiency of dehumidification. Highly sensitive temperature measurement control panel uses Schneider components, high sensitivity, stable and reliable. Using CAREL brand greenhouse sensor accurate measurement and control technology, the temperature adjustable range is 16C ° -30C °. Humidity controllable range RH30-95%. Humidity control accuracy ± 3% RH. Temperature accuracy ± 1 ℃. It has the characteristics of more reliable performance and more flexible functions. Equipment parameter table:

风冷恒温恒湿机

Performance introduction: The air-cooled constant temperature and humidity unit is mainly used to stabilize the temperature and humidity in the air and purified air processing equipment. It integrates cooling, heating, humidification, dehumidification, purification and fresh air functions into one, which can achieve accurate and reliable constant temperature and humidity control. Meet a variety of user environmental requirements. Product features: Classification description: A. According to environmental control requirements, it can be divided into high precision, ordinary precision, high precision and reliable; B. It can be divided into air-cooled and water-cooled according to the cooling method; C, it can be divided into conventional series according to use, Purification series, high temperature series, low temperature series, low humidity series; D. According to the dehumidification characteristics, it can be divided into refrigeration, runner, and combined constant temperature and humidity unit series; E. According to the physical structure, it can be divided into cabinet type and horizontal type; according to the return air The method can be divided into direct blow type and pipeline type 2. High-quality configuration: A. The heating method is divided into electric heating, hot water heating, and steam heating according to the use conditions, and the heating amount can be selected B, and the humidification method is divided into according to the use conditions : Wet film humidification, dry steam humidification, electrode humidification, etc., and the amount of humidification is optional C, the unit can be customized according to user requirements H407 working fluid such as R407c, R134a unit D, control system using Italian "carel" intelligent shielding can Programming the microcomputer controller, as long as the user sets the required temperature and humidity control range, the unit can automatically run according to the * economical operation mode; the controller uses a serial communication output interface, which can be remotely connected to the network. Control parameters:

风冷调温除湿机

Performance introduction: Air-cooled thermostat dehumidifier is through air-cooled thermostat (with outdoor condenser), which controls the temperature rise or fall while dehumidifying. It has the function of air conditioning, integrating dehumidification and refrigeration. There are several types of air output, top air output, and duct air supply. Users can choose according to specific conditions. Product features: 1. The optional fully enclosed refrigeration compressor, expansion valve, solenoid valve and other parts of the unit are imported products. 2. The control switch adopts touch buttons, and the operation panel has the function of operation indication and fault display. 3. The fan equipped with the unit adopts high-performance, low-noise centrifugal fan, which has the advantages of low noise, large air volume and high static pressure. 4. The unit can achieve central control, and configure communication interfaces according to user requirements to achieve centralized control and display of long-distance computers. 5. The unit operates smoothly, is easy to operate, has a beautiful appearance, and has a small maintenance workload. Technical parameters:

组合式转轮除湿机

Principle of combined rotor dehumidifier: The main structure of the rotor dehumidifier is a continuously rotating honeycomb drying rotor, which is composed of a corrugated medium made of a special composite heat-resistant material. The corrugated medium contains a hygroscopic agent. The two sides of the dehumidification rotor made of highly sealed elastic material are divided into two sectors, one is a 270 ° sector at the wet air end, and the other is a 90 ° sector at the regeneration air end. When the humid air to be treated enters the 270 ° sector of the runner, the water molecules in the air are absorbed by the hygroscopic agent in the runner, and the dried air is sent to the dry air outlet through the fan. The wheel rotates at a speed of 8-18 cycles / hour. The fan surface in the processing air area absorbs water molecules and becomes saturated, and then automatically transfers to the fan-shaped area at the regeneration air end to enter the regeneration process. During the regeneration process, after the regeneration air is heated (about 120 ° C), it enters the fan surface of the runner regeneration zone. At high temperatures, water molecules in the runner are desorbed and lost to the regeneration air. Because the regeneration air loses heat during the desorption process, its temperature decreases, and it becomes humid air with a large moisture content, which is discharged to the outside by the regeneration fan. Dehumidification and regeneration occur simultaneously. The air to be treated is continuously dehumidified, and the rotor is continuously regenerated to continuously dehumidify the air. Product features: 1. PLC programmable controller, human-machine interface at a glance; 2. Intelligent control of regenerative heating, automatic adjustment of temperature and humidity; 3. The unit is equipped with a regenerative over-temperature alarm, and the rotor stops rotating; 4. The air inlet is installed There are filters to prevent dust and reduce the number of cleaning and maintenance; 5. The unit adopts aluminum alloy frame, which is strong and beautiful; 6. The Proflute dehumidification wheel imported from Sweden has super dehumidification capacity; 7. The dehumidification wheel has a long service life, which can reach 8- 18 years; 8. RS485 communication interface is reserved for the unit, which can be connected to the computer; 9. The unit can be connected with refrigeration equipment and purification equipment; 10. Easy operation and maintenance, which can be operated and maintained without professionals; Equipment schematic diagram: Equipment parameter table : Applications: This product is widely used in machine rooms (electricity, telecommunications, etc.), workshop warehouses (electronics, footwear, clothing, tobacco, food, leather, paper products, etc.), ships, port machinery, biopharmaceuticals, medical, precision instruments , Bridge, electronic product processing, candy drying, shipbuilding, spraying and other industries.

空气能热泵烘干机

Working principle of heat pump dryer: The heat pump is essentially a heat lifting device. The high temperature heat pump drying unit uses the reverse Carnot principle to draw heat from the surrounding environment and transfer it to the heated object (higher temperature objects). ), Its working principle is the same as the refrigerator, all work according to the reverse Carnot cycle, the only difference is the operating temperature range. It is upgraded to high-temperature thermal energy by the heat pump device; the refrigerant (fluramine) is converted into high-temperature and high-pressure gas (temperature up to 80-115 ° C) by the compressor, and enters the indoor heat exchanger, using the exhaust heat of the fan to heat up Dry the room air temperature. The material in the drying room is vaporized by evaporation of the water in the material through the work of hot air, and the evaporated water vapor is discharged by the dehumidification system to achieve the purpose of drying the material. When the high-temperature heat pump drying unit works, like ordinary air conditioners and heat pump units, it absorbs the energy in the low-temperature environment medium in the evaporator QA: It consumes a part of the energy itself, that is, the power consumption of the compressor QB: The heat release QC in the condenser, QC = QA + QB, so the efficiency of the high temperature heat pump drying unit is (QB + QC) / QB, and the heating efficiency of other heating equipment is less than 1, so the high temperature heat pump drying unit is heating The efficiency is far greater than the efficiency of other heating equipment. It can be seen that using a high-temperature heat pump drying unit as a drying device can save energy, and at the same time reduce the emissions of CO2 and other pollutants, achieving the effect of energy saving and emission reduction. Jibei Air Energy Dryer Parameter Table: Note: The above parameters are based on dry bulb temperature of 25 ℃ and wet bulb temperature of 20 ℃. Control system features: 1. Stable performance, easy operation, multi-function control can be achieved, and different types of materials drying process requirements can be met. 2. PLC programmable control method can be used to set different drying curves, such as temperature and humidity settings. 3. The heat pump in the heat pump drying device not only has the drying function, but also has the cooling and heating functions, and realizes various functions such as low temperature processing and greenhouse heating. 4, with power-off memory function, one-button setting, intelligent management. Features of heat pump dryer: 1. Convenient installation: easy installation and removal, small footprint, can be installed indoors or outdoors; 2. ** energy saving: only need to consume a small amount of electrical energy, it can absorb a large amount of heat in the air , The power consumption is only 1/4 of the electric heater; compared with coal, oil, and gas dryers, it can save about 60% of operating costs. 1 kWh is equal to 4 kWh. 3. Environmental protection and no pollution: without any burning matter and emissions, it is a sustainable and environmentally friendly product. 4. Safe and reliable operation: The entire system operates without the dangers of flammable, explosive, poisoning and short circuit that may exist in traditional dryers (fuel, gas or electric heating). It is a safe and reliable semi-closed drying system. . 5. Long service life and low maintenance cost: It is developed on the basis of traditional air-conditioning technology with stable, reliable performance and long service life; safe and reliable operation, fully automatic and manual operation, and intelligent control. 6, comfortable and convenient, high degree of automation and intelligence: self-controlled constant temperature device, continuous drying operation for 24 hours. 7, a wide range of applications, not affected by climate: can be widely used in food, agricultural and sideline products, seafood, paper and wood, leather chemical medicine and other high-temperature hot water and drying system equipment. Application fields of heat pump dryers: medicinal material dryers: Sanqi dryers, octagonal dryers, Morinda dryers, Dendrobium dryers, Yam Huaishan dryers, Ganoderma dryers, sea cucumber dryers, Honeysuckle dryer, Luo Han Guo dryer, cinnamon dryer, ginseng dryer, sand ginger dryer, maca dryer, wolfberry dryer, angelica dryer and so on. Agricultural Product Dryer: Overlord Flower Dryer, Rose Dryer, Chrysanthemum Dryer, Shiitake Dryer, Bamboo Dryer, Sweet Potato Dryer, Okra Dryer, Tobacco Dryer, Tremella Dryer Machine, fungus dryer, pepper dryer, daylily dryer, tea tree mushroom dryer, taro dryer, vegetable dryer, bamboo shoot dryer, cassava dryer, starch dryer , Edible fungus heat pump dryer, vegetable dryer and so on. Fruit dryer: longan dryer, lychee dryer, banana slice dryer, mango dryer, jujube dryer, jujube dryer, bayberry dryer, lemon dryer, grape dryer Machine, jackfruit dryer, kiwi dryer, persimmon dryer, olive dryer, preserved fruit dryer, etc. Food dryer: sausage dryer, bacon dryer, bacon dryer, sausage dryer, casing dryer, river noodle dryer, rice noodle dryer, sweet potato noodle dryer, noodle oven Dryer, noodle dryer, yuba dryer, etc. Seafood dryer: sea fish dryer, squid dryer, shrimp dryer, dried squid dryer, sea cucumber dryer, cuttlefish dryer, seahorse dryer, Yaozhu dryer, etc. . Tea dryer: Pu'er tea dryer, black tea dryer, Dahongpao dryer, Jin Junmei dryer, Tieguanyin dryer, green tea dryer, hair tip dryer, etc. Buddha incense dryer: Buddha incense dryer, plate incense dryer, incense dryer, bamboo stick incense dryer, stick incense dryer, craft incense dryer, mosquito incense dryer and so on. Wood dryers: rosewood dryer, rosewood furniture dryer, rosewood dryer, rosewood dryer, black rosewood dryer, red rosewood dryer, ebony dryer, stripe Ebony Dryer, Chicken Wing Dryer, Redwood Upper Product Dryer, Redwood Furniture Paint Drying Room, Wood Floor Dryer, Wood Product Dryer, Bamboo Product Dryer, Bamboo Tumble Dryer, Bamboo Rubber board dryer, bamboo floor dryer, veneer dryer, eucalyptus rotary cutting board dryer, building template dryer and so on. Industrial product dryer: printing dryer, leather dryer, cloth dryer, gypsum dryer, plastic dryer, electroplating dryer, craft dryer, firework dryer, paper tube dryer Machine, rubber dryer, etc. Production line dryer (tunnel dryer, belt line dryer): rubber glove dryer, noodle tunnel dryer, straight rice flour dryer, gypsum block tunnel dryer, leather tunnel dryer Dryer and much more. Installation diagram: installation example:

风冷型冷冻式干燥机

Working principle of room temperature air-cooled refrigerated dryer: The amount of water vapor in the compressed air is determined by the temperature of the compressed air. While keeping the pressure of the compressed air basically unchanged, lowering the temperature of the compressed air can reduce the amount of air in the compressed air. Water vapor content, and excess water vapor will condense into a liquid. The refrigerating dryer is based on the correspondence between the saturated steam pressure and temperature of the water, and uses a refrigeration device to cool the compressed air to a certain dew point temperature, precipitating the contained water, and discharging the water through a steam-water separator and an electric drain. , So that the compressed air is dried. Features of air-cooled refrigerating dryer: 1. Ensure the normal operation of the equipment at an ambient temperature of 40 degrees Celsius 2. Use natural air as a cooling medium for the refrigeration system, without the need for a complete set of facilities for water supply, water recovery and cooling, convenient and economical ; 3. The heat exchanger adopts countercurrent design, high heat exchange efficiency and small volume; 4.The steam-water separator adopts three-stage separation method: direct collision separation + low-speed centrifugal separation + stainless steel wire mesh demister, and 99.9 & The liquid water is separated from the cooled compressed air to prevent the secondary evaporation of the water and ensure the low dew point quality of the finished gas; 5. The refrigeration compressor adopts French PERFORMER and German BITZER ), Copeland, MANEUROP, Taiwan CHYNTEC and other companies fully or semi-hermetic refrigeration compressors, stable operation, low noise, high COP, reliable performance, power saving, long life ; 6. Refrigeration control components are made of Danfoss, Denmark, EMERSON, SPORLAN, etc .; 7. Special machines PLC control can be used, operating parameters of real-time display, remote control; working conditions and technical specifications normal air-cooled refrigeration dryer model parameters

微热再生吸附式干燥机

Working principle: The micro-heat regeneration adsorption type compressed air dryer uses the pores held by the desiccant material itself to adsorb the water molecules in the air according to the capillary action, and at the same time desorbs the adsorption according to the pressure release and desorption and the temperature of the adsorption waste heat. Moisture. The equipment is generally made in the form of a double cylinder. Under the control of a program controller, the two cylinders work alternately. One cylinder absorbs water, and the other desorbs and regenerates. It works continuously and cyclically. Product Features of Micro-heat Regeneration Adsorption Dryer 1. Pressure dew point can reach -40 degrees Celsius; 2. Regeneration gas consumption ≤ 7%; 3. High-quality switching valve, stable and reliable, can ensure the integrity of the work process, and extend the components. Working life; use active alumina with high hygroscopicity, uniform shape and size, high strength, high output dew point, less dust generation, long service life; 4. Unique regenerative pipe design to ensure the heating and cold blowing of regenerative gas plane When the regeneration gas is used, the distribution of the regeneration gas can be evenly distributed, so that the adsorption and heating of the central part of the adsorption tower is even, heat dissipation is fast, and the regeneration is thorough; Reduce energy consumption; 6, programmable microcomputer controller, cycle time, adsorption, regeneration working time, heating time, heating temperature can be adjusted. To achieve the required gas requirements. Operating conditions and technical indicators Model and parameters of micro-heat regeneration adsorption dryer

组合式低露点干燥机

Working principle of the combined low dew point dryer: The combined low dew point dryer is composed of a cooling dryer and an adsorption (no heat or heat) dryer through reasonable pipeline connection and volume matching. Cooling dryers have extremely strong water removal capacity, low operating energy consumption, and no loss of air volume. Combined with the characteristics that adsorption dryers can reach lower dew points, the advantages of both can be used to the limit. Before the compressed air enters the adsorption dryer, use a cooling dryer to perform pre-treatment, so that a large amount of water (about 80%) is first removed in the refrigerated dryer. After entering the adsorption dryer for deep drying, it can A very low pressure dew point is reached, up to -70 ° C. It uses a freeze dryer as a pre-water removal device for an adsorption dryer. The strong water removal capacity of the refrigerating dryer drastically reduces the inlet water load of the drying tower. After cooling, the water entering the adsorption tower is about 20% of the ordinary dryer. Under other conditions, it is used for absorption. Low dew-point dry air with water vapor can also decrease by the same magnitude. That is, the amount of regeneration gas is about 1/5 of that of ordinary adsorption dryers. Therefore, it has indeed created conditions for reducing the energy consumption of regeneration, especially the energy consumption of regeneration gas. So as to achieve the best economic operating point and high-quality low-dew point product gas. Product features 1. Low dew point: The combined low dew point dryer can reach a very low pressure dew point, which can routinely reach below -40 ° C, and can reach -70 ° C according to different user requirements. 2. Low energy consumption: The regeneration air consumption of the combined low-dew-point dryer only needs 3% to 5%, which greatly saves the compressed air consumption. 3. Compressed air with different dew points can be provided for different air points. 4. All the operation switches and display instruments of the combined low dew point dryer are concentrated on the panel of the box board. The cooling dryer and the adsorption regeneration dryer can be operated independently or at the same time as cold and suction according to customer needs. . 5. The gas-liquid separator combines two separation technologies: cyclone separation and filter element separation. It can fully separate the cooled liquid water and give full play to the efficiency of freeze drying. 6. Refrigeration compressors adopt medium- and high-temperature full-closed and well-known brands such as PERFORMER, BITZER, COPELAND, MANEUROP, and CHYNTEC of Taiwan. Semi-hermetic refrigeration compressor. 7. The heat exchanger and condenser of the refrigerating dryer are made of high quality ** threaded pipes. 8. The adsorption dryer part adopts a scientific and reasonable design of the structure of the adsorption tower, and the design of the compressed air diffuser, separation plate, and airflow section coils ensures that the adsorbent is in full contact with the compressed air to avoid tunnel effects and effectively reduce The impact of high-speed airflow on the adsorbent reduces the wear of the adsorbent, prolongs the life of the adsorbent, and ensures the stability of the air dew point. 9. The adsorption dryer part can adjust the amount of regeneration gas according to the operating load requirements of the equipment and the level of the air dew point to achieve energy saving effects. 10. The adsorption dryer uses high-performance adsorbent, which has a larger active surface area, higher strength and longer service life. 11. Control method: According to different gas requirements of users, a variety of different control methods are adopted. Air-cooled Combined Low Dew Point Dryer Schematic Conditions and Technical Specifications Air-cooled Combined Low Dew Point Dryer Model Parameters

余热再生吸附式干燥机

Working principle of waste heat regeneration adsorption dryer: The high-temperature compressed air discharged from the air compressor has two properties of heat and high unsaturation. Compressed heat products effectively use this original compressed air to heat and regenerate the adsorbent, which saves The power consumption of the electric heater required by the micro-heat dryer series eliminates the gas consumption at this stage. After the heating and regeneration is completed, the original compressed air directly enters the water cooler and then enters the adsorption tower to be adsorbed to obtain the dried product gas. At the same time, we take 3 % Of the product gas is cold-blow regeneration of the adsorbent that has been heated, and the double-tower switchover is completed after the cold blow. Characteristics of waste heat regeneration adsorption dryer: 1. ** Energy saving; 2.Pressure dew point can reach -20 ℃ ~ -40 ℃; 3.Average regeneration gas consumption ≤1.5%; 4.High quality switching valve, stable and reliable, can guarantee Integrity of the work flow to extend the working life of the components; 5. Use highly hygroscopic activated alumina, uniform shape and size, high strength, low output dew point, less dust generation, and long service life; 6. Unique regeneration The piping design ensures that the regeneration gas can be evenly distributed during the heating and cold blowing of the regeneration gas, so that the adsorbent in the center of the adsorption tower is evenly heated, heat is radiated quickly, and the regeneration is complete; 7, three-stage drainage function; 8, low pressure loss; Conditions and technical indicators Model parameters of waste heat regeneration adsorption dryer

压缩空气预冷机

Working principle of compressed hot air pre-cooler: JBAY air separation pre-cooler uses the principle of refrigeration cycle to cool high-temperature compressed air and remove condensate to provide users with dry and low-temperature compressed air. It is mainly used for air separation and compression. Air has low temperature requirements. Product features: The refrigeration system uses imported well-known brand compressors, which have the characteristics of stable refrigeration performance, high energy efficiency ratio, and low operating noise. Automatic control, compact structure, beautiful chassis, no foundation installation. Working conditions and technical indicators Compressed air precooler model parameters

防爆商用除湿机

Product introduction: The products have passed the ISO9001: 2015 quality management system certification. The products have passed the explosion-proof certificate issued by the country. The products have passed the national compulsory CCC product certification. The explosion-proof air-conditioning dehumidification products meet the current national standards for the implementation of explosion-proof products: GB3836. 1-2010 <Explosive Environment Part 1: General Requirements for Equipment> GB3836.2-2010 <Explosive Environment Part 2: Equipment Protected by Flameproof Enclosure "d"> GB3836.4-2010 <Explosive Environment Part 4: By Intrinsically safe "i" protected equipment> GB3836.9-2014 <Explosive environment part 9: Equipment protected by potting "m"> Performance characteristics: Reserve R485 communication interface to achieve centralized control of humidity sensor failure self-diagnosis Function Microcomputer automatic defrost, more reliable and accurate. All metal components and electrostatic sprayed sheet metal casing. International ** Imported compressor hose continuous drainage function. Equipped with universal wheels at the bottom, free movement. Frequency conversion technology can save 10% of electricity. And condenser aluminum fin hydrophilic film, condenser / evaporator, anti-stain cleaning ability 0.1mm hydrophilic aluminum foil material, fast condensation, greatly improved efficiency, internally threaded copper pipe, greatly improved The efficiency of dehumidification is adopted. The compressor and main accessories of the powerful power compressor are used in the scientific and reasonable design of the refrigeration system to operate normally in different environments. It overcomes the shortcomings of the compressor industry, such as insufficient cooling capacity, dehumidification capacity, and frequent startup of the product. The product uses a long time turbo centrifugal fan with a U-shaped air duct, which reduces noise and noise, and the strong wind greatly improves the dehumidification rate. The large circulating air volume, the high-sensitivity temperature measurement control panel uses Schneider components, high sensitivity, stable and reliable explosion-proof power supply. Junction box performance is stable, safe and reliable Explosion-proof plugs Tight protective cover, metal shell, pure copper solid core Product parameter table:

防爆工业除湿机

Product introduction: The products have passed the ISO9001: 2015 quality management system certification. The products have passed the explosion-proof certificate issued by the country. The products have passed the national compulsory CCC product certification. The explosion-proof air-conditioning dehumidification products meet the current national standards for the implementation of explosion-proof products: GB3836. 1-2010 <Explosive Environment Part 1: General Requirements for Equipment> GB3836.2-2010 <Explosive Environment Part 2: Equipment Protected by Flameproof Enclosure "d"> GB3836.4-2010 <Explosive Environment Part 4: By Intrinsically safe "i" protected equipment> GB3836.9-2014 <Explosive environment part 9: Equipment protected by potting "m"> Performance characteristics: Reserve R485 communication interface to achieve centralized control of humidity sensor failure self-diagnosis Function Microcomputer automatic defrost, more reliable and accurate. All metal components and electrostatic sprayed sheet metal casing. International ** Imported compressor hose continuous drainage function. Equipped with universal wheels at the bottom, free movement. Frequency conversion technology can save 10% of electricity. And condenser aluminum fin hydrophilic film, condenser / evaporator, anti-stain cleaning ability 0.1mm hydrophilic aluminum foil material, fast condensation, greatly improved efficiency, internally threaded copper pipe, greatly improved The efficiency of dehumidification is adopted. The compressor and main accessories of the powerful power compressor are used in the scientific and reasonable design of the refrigeration system to operate normally in different environments. It overcomes the shortcomings of the compressor industry, such as insufficient cooling capacity, dehumidification capacity, and frequent startup of the product. The product uses a long time turbo centrifugal fan with a U-shaped air duct, which reduces noise and noise, and the strong wind greatly improves the dehumidification rate. The large circulating air volume, the high-sensitivity temperature measurement control panel uses Schneider components, high sensitivity, stable and reliable explosion-proof power supply. Junction box performance is stable, safe and reliable Explosion-proof plugs Tight protective cover, metal shell, pure copper solid core Product parameter table:

防爆调温除湿机

Product introduction: The products have passed the ISO9001: 2015 quality management system certification. The products have passed the explosion-proof certificate issued by the country. The products have passed the national compulsory CCC product certification. The explosion-proof air-conditioning dehumidification products meet the current national standards for the implementation of explosion-proof products: GB3836. 1-2010 <Explosive Environment Part 1: General Requirements for Equipment> GB3836.2-2010 <Explosive Environment Part 2: Equipment Protected by Flameproof Enclosure "d"> GB3836.4-2010 <Explosive Environment Part 4: By Intrinsically safe "i" protected equipment> GB3836.9-2014 <Explosive environment part 9: Equipment protected by a potting "m"> Performance characteristics: Explosion-proof temperature-controlled dehumidifier is air-cooled and temperature-controlled (with outdoor Condenser), which controls the temperature rise or fall while dehumidifying. It has the function of air conditioning. It integrates dehumidification and cooling. The air supply mode includes front air outlet, top air outlet, and duct air supply. The user can Choose the situation. Product features: 1. The optional fully enclosed refrigeration compressor, expansion valve, solenoid valve and other parts of the unit are imported products. 2. The control switch adopts touch buttons, and the operation panel has the function of operation indication and fault display. 3. The fan equipped with the unit adopts high-performance, low-noise centrifugal fan, which has the advantages of low noise, large air volume and high static pressure. 4. The unit can achieve central control, and configure communication interfaces according to user requirements to achieve centralized control and display of long-distance computers. 5, the unit runs smoothly, easy to operate, beautiful appearance, small maintenance workload equipment parameter table

防爆恒温恒湿机

Product introduction: The products have passed the ISO9001: 2015 quality management system certification. The products have passed the explosion-proof certificate issued by the country. The products have passed the national compulsory CCC product certification. The explosion-proof air-conditioning dehumidification products meet the current national standards for the implementation of explosion-proof products: GB3836. 1-2010 <Explosive Environment Part 1: General Requirements for Equipment> GB3836.2-2010 <Explosive Environment Part 2: Equipment Protected by Flameproof Enclosure "d"> GB3836.4-2010 <Explosive Environment Part 4: By Intrinsically safe "i" protected equipment> GB3836.9-2014 <Explosive environment part 9: Equipment protected by the casting "m"> Performance characteristics: Explosion-proof constant temperature and humidity unit is mainly used to stabilize the temperature and humidity in the air and purification The air treatment equipment integrates cooling, heating, humidification, dehumidification, purification and fresh air functions, which can achieve accurate and reliable constant temperature and humidity control to meet users' different environmental requirements. Product characteristics: 1. Classification description: A. It can be divided into high precision, ordinary precision, high precision and reliable type according to environmental control requirements; B. It can be divided into air-cooled and water-cooled type according to cooling method; C. It can be divided into conventional according to use. Series, purification series, high temperature series, low temperature series, low humidity series; D, according to dehumidification characteristics can be divided into refrigeration, runner, combined constant temperature and humidity unit series; E, according to the structure can be divided into cabinet type, horizontal type; according to delivery The return air method can be divided into direct blowing type and duct type 2. High-quality configuration: A. The heating method is divided into electric heating, hot water heating, and steam heating according to the use conditions, and the heating amount can be selected B, and the humidification method is based on the use conditions Divided into: wet film humidification, dry steam humidification, electrode humidification, etc., and the amount of humidification is optional C, the unit can be customized according to user requirements HFC working medium such as R407c, R134a unit D, the control system uses Italian "carel" intelligent Shielded programmable microcomputer controller, as long as the user sets the required temperature and humidity control range, the unit can automatically run according to the * economical operation mode; the controller uses a serial communication output interface, which can be networked Remote control equipment parameter table

防爆柜式空调机

Product introduction: The products have passed the ISO9001: 2015 quality management system certification. The products have passed the explosion-proof certificate issued by the country. The products have passed the national compulsory CCC product certification. The explosion-proof air-conditioning dehumidification products meet the current national standards for the implementation of explosion-proof products: GB3836. 1-2010 <Explosive Environment Part 1: General Requirements for Equipment> GB3836.2-2010 <Explosive Environment Part 2: Equipment Protected by Flameproof Enclosure "d"> GB3836.4-2010 <Explosive Environment Part 4: By Intrinsically safe "i" protected equipment> GB3836.9-2014 <Explosive atmospheres Part 9: Equipment protected by a potting "m"> Performance characteristics: Evaporator & condenser aluminum fin hydrophilic film, condenser / Evaporator, anti-stain cleaning ability 0.1mm hydrophilic aluminum foil material, fast condensation, greatly improve the internal thread copper tube, greatly improve the efficiency of dehumidification. Use a powerful power compressor, compressors and main accessories through a scientific and reasonable design of the refrigeration system. The normal operation of different environments overcomes the shortcomings of insufficient refrigeration and dehumidification capacity of the compressor industry models, the frequent startup of the unit and high product failure rate, and also improves the product's service life. Schneider temperature sensitive control panel components, high sensitivity, reliable power mining explosion proof junction box closed stable, safe and reliable explosion-proof plug tight protective cover, a metal shell, solid core copper apparatus datasheets

about us
Product center
Service Center
CONTACT
contact us
  • Sales Hotline: 4008-829-816
  • Company email: jibei118@sina.com
  • Address of Company: A3-2016, Lane 1588, South Wangyuan Road, Fengxian District, Shanghai
You are the 56457 visitor!